In the early 1940s, the Missouri Pacific Railroad converted all 25 of its 2-8-4 Berkshires into 4-8-4 Northerns. These rebuilt locomotives (road numbers 2101 through 2125) were given 75" drivers, greater boiler capacity, a cast steel engine bed and roller bearings on all axles. They had 28 x 30 cylinders, a boiler pressure of 250 psi, a total ...Factor of adh. The Norfolk and Western class J was a class of fourteen 4-8-4 "Northern" streamlined steam locomotives built by the Norfolk and Western Railway (N&W) at its Roanoke Shops in Roanoke, Virginia between 1941 and 1950. They performed flawlessly, making them the most powerful 4-8-4 steam locomotives ever produced.The Canadian National Class U-4a was a class of five streamlined 4-8-4 Northern type steam locomotives they were built by the Montreal Locomotive Works in 1936 for the Canadian National Railway, numbered 6400 to 6404. These engines were used for crack passenger service on the Canadian National Railway for much of their careers. The Canadian National U-4 class was a result of wind tunnel ... October 4, 2000. Atchison, Topeka and Santa Fe 3751 is a class 3751 4-8-4 "Heavy Mountain" type steam locomotive built in May 1927 by the Baldwin Locomotive Works in Eddystone (Philadelphia), Pennsylvania for the Atchison, Topeka & Santa Fe Railway (ATSF). No. 3751 was the first 4-8-4 steam locomotive built for the Santa Fe and was referenced ...The Ferrocarriles Nacionales de Mexico (National Railways of Mexico) bought a total of 32 Northern type, Class QR-1, locomotives in 1946. NdeM purchased 16 from the American Locomotive Company and 16 from the Baldwin Locomotive Works. On the NdeM these locomotives were called "Niágaras" and were among the few that it bought new.The Ferrocarriles Nacionales de Mexico (National Railways of Mexico) bought a total of 32 Northern type, Class QR-1, locomotives in 1946. NdeM purchased 16 from the American Locomotive Company and 16 from the Baldwin Locomotive Works. On the NdeM these locomotives were called "Niágaras" and were among the few that it bought new.The wheel arrangement of small diesel and petrol locomotives can be classified using the same notation as steam locomotives, e.g. 0-4-0, 0-6-0, 0-8-0. Where the axles are coupled by chains or shafts (rather than side rods) or are individually driven, the terms 4w (4-wheeled), 6w (6-wheeled) or 8w (8-wheeled) are generally used.A private Railway operating in New Zealand at the time exclusively purchased Baldwin products after facing the same difficulties with British builders the NZR had. The Wellington & Manawatu Railway (1881–1909) operated small fleets of 2-8-0 (4), 2-6-2 (6), 2-8-2 (1), 4-6-0 (2) and a large 2-8-4 (1) tank locomotive. When the NZR took over the ...4-4-4T Cóndor of the Gran Ferrocarril de Venezuela in 1901. The 3 ft 6 in (1,067 mm) gauge Gran Ferrocarril de Venezuela (Great Venezuela Railway) acquired a class of three 4-4-4T locomotives in 1892, the Cóndor, Gavilán and Halcón. They were built by Hartmann's Sächsische Maschinenfabrik in Chemnitz, Germany. Their maximum speed was 70 ... Shop online for 62 4-8-4 model train locomotives at discounts up to 28%. Steam - HO is the most popular of the 3 4-8-4 model train locomotives categories, then Steam - N, and Diesel - N. Broadway Limited Imports is ranked #1 out of 4 4-8-4 model train locomotives manufacturers, followed by Kato USA Inc, and Athearn.Jun 12, 2006 · Fred McLeod. Union Pacific 4-8-8-4 No. 4023 prepares to depart Cheyenne, Wyo., with a westward freight in May 1954. E.C. Storm. It was, more or less, an eight-coupled Challenger. The locomotive boasted both the adhesion of an eight-coupled articulated, needed to haul heavy trains, and large 68-inch driving wheels (only 1-2 inches smaller than ... Reading 2101 is a preserved American class "T-1" 4-8-4 "Northern" type steam locomotive constructed in 1945 for use by the Reading Company.Constructed from an earlier "I10SA" 2-8-0 "Consolidation"-type locomotive built in 1923, the 2101 handled heavy coal train traffic for the Reading until being retired from revenue service in 1959.The Canadian National Class U-4a was a class of five streamlined 4-8-4 Northern type steam locomotives they were built by the Montreal Locomotive Works in 1936 for the Canadian National Railway, numbered 6400 to 6404. These engines were used for crack passenger service on the Canadian National Railway for much of their careers. The Canadian National U-4 class was a result of wind tunnel ... The St. Louis Southwestern Railroad acquired Northerns at three different times. It bought 10 Class L-1 Northerns in 1930 from the Baldwin Locomotive Works and assigned them road numbers 800 through 809. These 4-8-4s were oil burners with 70" drivers, 26 x 30 cylinders, a boiler pressure of 250 psi, a weight of 419,800 lbs and a tractive effort ... The 2-8-4's 4-wheel trailing truck permitted a huge firebox to be located after the boiler. The resulting greater steaming rate ensured that such a locomotive would never run out of power at speed, a common failing of older locomotives. Applying the ideas of the freight-minded Berkshire type to the Pacific resulted in a 4-6-4 locomotive.In the early 1940s, the Missouri Pacific Railroad converted all 25 of its 2-8-4 Berkshires into 4-8-4 Northerns. These rebuilt locomotives (road numbers 2101 through 2125) were given 75" drivers, greater boiler capacity, a cast steel engine bed and roller bearings on all axles. They had 28 x 30 cylinders, a boiler pressure of 250 psi, a total ... The New York Central Railroad's Niagara was a 4-8-4 "Northern" type steam locomotive named after the Niagara River and Falls. It had a 4-8-4 wheel arrangement and is considered as one of the most efficient 4-8-4 locomotives ever built. The first New York Central Railroad Northern was ordered in 1931: No. 800, [1] an experimental locomotive that ...Swiss classification: 4/9; This wheel arrangement was proposed by Lima Locomotive Works in 1949 as a continuation of their "Super Power" concept, essentially an expansion of the 4-8-4. A larger firebox similar to the ones on the 2-6-6-6 locomotives built by Lima would have been fitted, allowing for greater power at speed. Despite promotion by ... Feb 9, 2018 · Rio Grande Info cited Robert Schaefer's "D&RGW 4-8-4 Westerns" in "The Prospector", Volume 2 Number 2 for the very interesting origin story of this class. Originally the D&RGW was attracted to Alco's variation on the Delaware, Lackawanna & Western's 4-8-4, in part because Alco had developed a single-piece cylinder and frame casting. The Union Pacific Railroad bought 45 4-8-4s in three orders from the American Locomotive Company. The second order of 15 locomotives (road numbers 820 through 834) was delivered in 1939. These locomotives were designated as Class FEF-2. They were designed to have 80" drivers, 25 x 32 cylinders, a boiler pressure of 300 psi, and a weight of 483,Nacional de Mexico 4-8-4 Locomotives in Mexico. The Ferrocarriles Nacionales de Mexico (National Railways of Mexico) bought a total of 32 Northern type, Class QR-1, locomotives in 1946. NdeM purchased 16 from the American Locomotive Company and 16 from the Baldwin Locomotive Works. On the NdeM these locomotives were called "Niágaras" and were ... She was the last of three K-4-b class Pacifics built for the Grand Trunk Western by Baldwin Locomotive Works in 1929. They featured enclosed or vestibule cabs similar to those on GTW's 4-8-4s and 4-8-2s, and also introduced the exhaust steam injector in place of the feedwater heater of the K-4-a class. This photo was taken in the summer of 1953.Shop online for 62 4-8-4 model train locomotives at discounts up to 28%. Steam - HO is the most popular of the 3 4-8-4 model train locomotives categories, then Steam - N, and Diesel - N. Broadway Limited Imports is ranked #1 out of 4 4-8-4 model train locomotives manufacturers, followed by Kato USA Inc, and Athearn.Union Pacific 844 is a class "FEF-3" 4-8-4 "Northern" type steam locomotive owned and operated by the Union Pacific Railroad for its heritage fleet.Built in December 1944 by the American Locomotive Company (ALCO) of Schenectady, New York, No. 844 is one of four surviving FEF series locomotives and the only one in operation. Get Updates. Canadian National U-class 4-8-4 locomotives proved to be the most versatile of the type operated in North America. It’s generally accepted that the ultimate in steam power was the 4-8-4 Northern type, if defined by criteria that includes speed, power, technology, and, perhaps most importantly, versatility.What Features Do the Steam Locomotives Have? Live Steam: Steam locomotives that produce live steam look life-like when moving around the track. The puffing smoke comes out the die-cast metal stack. Wheel Arrangement: Models with 4-8-4 configurations means there are 4 leading, 8 driving, and 4 trailing wheels. You'll find other steam locomotives ...The Great Northern Railway obtained its first "Northerns" in 1929, when six Class S-1s were delivered from the Baldwin Locomotive Works. These 4-8-4s were given road numbers 2550 through 2555 and had 73" drivers, 28 x 30 cylinders, a boiler pressure of 250 psi, a weight of 472,120 lbs and a tractive effort of 68,466 pounds.The Santa Fe 2900 Class was a series of 30 4-8-4 type steam locomotives built between 1943 and 1944 for Atchison, Topeka and Santa Fe Railroad and pulled freight and passenger trains until retirement in the early to late-1950s. Today, six 2900s survive, with five units on static display and one, No. 2926, has been restored to operating ... Southern Pacific 4449, also known as the Daylight, is the only surviving example of Southern Pacific Railroad 's "GS-4" class of 4-8-4 "Northern" type steam locomotives and one of only two GS-class locomotives surviving, the other being "GS-6" 4460 at the National Museum of Transportation in St. Louis, Missouri. These locomotives were the first in a large series of 4-8-4s of very similar design that totalled more than 200 engines. U-2a (works #1800-1819) numbered from 6100 to 6119 and delivered from Canadian Loco Works in 1927. U-2b (6120-6139), delivered from Montreal in 1927 (works #67351-67370), identical except for 233,400-lb weight on drivers and ... Fred McLeod. Union Pacific 4-8-8-4 No. 4023 prepares to depart Cheyenne, Wyo., with a westward freight in May 1954. E.C. Storm. It was, more or less, an eight-coupled Challenger. The locomotive boasted both the adhesion of an eight-coupled articulated, needed to haul heavy trains, and large 68-inch driving wheels (only 1-2 inches smaller than ...Rivarossi’s 4-8-8-4 Big Boy has been around a long time, but with its fine wire details, smooth performance, and updated sound decoder, this is definitely a modern scale locomotive. Hobbyists modeling the Union Pacific’s steam era shouldn’t need a reason to want one (or more) of these brawny beauties in their roundhouses.Data from "4-8-4 Locomotives on the Northern Pacific," Baldwin Locomotives (1937), pp. 27-28 and NP to 1944 Locomotive Diagrams supplied in May 2004 by Allen Stanley from his extensive Rail Data Exchange. Works numbers were 62163-62166 in March 1938, 62167-62168. in April and 62169-62170 in May. As suggested by the 1937 account of the A-2s ... She was the last of three K-4-b class Pacifics built for the Grand Trunk Western by Baldwin Locomotive Works in 1929. They featured enclosed or vestibule cabs similar to those on GTW's 4-8-4s and 4-8-2s, and also introduced the exhaust steam injector in place of the feedwater heater of the K-4-a class. This photo was taken in the summer of 1953.N&W Class J 4-8-4 Designed for optimum-speed passenger service, the “J” was the last mainline steam locomotive to run in the United States. The Class J 4-8-4 has returned to the Bachmann HO line in a DCC Sound Value version that includes a SoundTraxx ® steam package with authentic prototypical chuff, short and long whistles, bell, air pump ...The 4-8-4's were given Class J and built by the master steam builders at N&W's Roanoke, Virginia shops. These machines could haul the mail, quite literally, and were the most powerful 4-8-4's ever built with tractive efforts reaching 80,000 pounds, boiler pressures of 300 psi, and perfectly couter-balanced to reach unimaginable speeds of 140 mph!A private Railway operating in New Zealand at the time exclusively purchased Baldwin products after facing the same difficulties with British builders the NZR had. The Wellington & Manawatu Railway (1881–1909) operated small fleets of 2-8-0 (4), 2-6-2 (6), 2-8-2 (1), 4-6-0 (2) and a large 2-8-4 (1) tank locomotive. When the NZR took over the ...Get Updates. Canadian National U-class 4-8-4 locomotives proved to be the most versatile of the type operated in North America. It’s generally accepted that the ultimate in steam power was the 4-8-4 Northern type, if defined by criteria that includes speed, power, technology, and, perhaps most importantly, versatility.The Nashville, Chattanooga & St. Louis Railroad bought five 4-8-4 locomotives in 1930, which they called "Dixies" (instead of "Northerns" - a name that would seem inappropriate on a fine southern railroad). These 1930 "Dixies" came from the American Locomotive Company and were designated Class J-2 and assigned road numbers 565 through 569. Nov 1, 2004 · It has flaws, but Broadway Limited Imports has shown an ability to learn from mistakes. Fans of western steam power will be happy to have it and to look forward to comparing BLI releases of Santa Fe (and Union Pacific) locomotives. HO Santa Fe 4-8-4. Price: $329.99. Manufacturer: The Lima-Southern Pacific GS-4 ("GS" meaning for "Golden State" or "General Service") is a type of semi-streamlined 4-8-4 Northern steam locomotive built by the Lima Locomotive Works in 1941 and 1942 specifically for the Southern Pacific (SP) Railroad. They were assigned road numbers 4430 through 4457. The GS-4s were principally employed on SP's famous "Daylight" streamliners from 1941, but in ... First run. 6 February 1981. The South African Railways Class 26 4-8-4 of 1981, popularly known as the Red Devil, is a 4-8-4 steam locomotive which was rebuilt from a Class 25NC locomotive by mechanical engineer David Wardale from England while in the employ of the South African Railways. The rebuilding took place at the Salt River Works in Cape ...Missouri Pacific 4-8-4 Northerns The Missouri Pacific Railroad converted all 25 of its 2-8-4 Berkshires into 4-8-4 Northerns in the early 1940s. The rebuilt locomotives (road numbers 2101 through 2125) were given 75" drivers, greater boiler capacity, a cast steel engine bed and roller bearings on all axles.Nacional de Mexico 4-8-4 Locomotives in Mexico. The Ferrocarriles Nacionales de Mexico (National Railways of Mexico) bought a total of 32 Northern type, Class QR-1, locomotives in 1946. NdeM purchased 16 from the American Locomotive Company and 16 from the Baldwin Locomotive Works. On the NdeM these locomotives were called "Niágaras" and were ... Number 4000 was delivered to Omaha at 6PM, September 5, 1941. The 25 Big Boys were built in two groups. The first group of 20 locomotives, called "Class 1", were built starting in 1941. They were numbered 4000-4019. The second group of 5 locomotives, "Class 2", were built in 1944. They were numbered 4020-4024. Rio Grande Info cited Robert Schaefer's "D&RGW 4-8-4 Westerns" in "The Prospector", Volume 2 Number 2 for the very interesting origin story of this class. Originally the D&RGW was attracted to Alco's variation on the Delaware, Lackawanna & Western's 4-8-4, in part because Alco had developed a single-piece cylinder and frame casting.Missouri Pacific 4-8-4 Northerns The Missouri Pacific Railroad converted all 25 of its 2-8-4 Berkshires into 4-8-4 Northerns in the early 1940s. The rebuilt locomotives (road numbers 2101 through 2125) were given 75" drivers, greater boiler capacity, a cast steel engine bed and roller bearings on all axles.4-8-4. The Northerns are steam locomotives that represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees ... Nov 21, 2010 · Thierry Stora, of the French Compound Locomotives homepage, contends that the problems lay in the difference between the specified minimum curve radius (80 m or 262 ft) and the actual minimum, which could be as low as 50 m (164 ft). As a result, these 4-8-4s were limited to 50 mph (80 kph) Rivarossi’s 4-8-8-4 Big Boy has been around a long time, but with its fine wire details, smooth performance, and updated sound decoder, this is definitely a modern scale locomotive. Hobbyists modeling the Union Pacific’s steam era shouldn’t need a reason to want one (or more) of these brawny beauties in their roundhouses.The St. Louis Southwestern Railroad acquired Northerns at three different times. It bought 10 Class L-1 Northerns in 1930 from the Baldwin Locomotive Works and assigned them road numbers 800 through 809. These 4-8-4s were oil burners with 70" drivers, 26 x 30 cylinders, a boiler pressure of 250 psi, a weight of 419,800 lbs and a tractive effort ...In 1930, the SP designed a locomotive similar to those Mountains that had a very large firebox (90.4 sq ft) and a four wheel trailing truck to support it. Thus, evolved the Southern Pacific 4-8-4 which was designated Class GS (Golden State) by the SP. In early 1937, six more "Golden States" arrived but this time from the Lima Locomotive Works.Union Pacific 4014 is a steam locomotive owned and operated by the Union Pacific (UP) as part of its heritage fleet. It is a four-cylinder simple articulated 4-8-8-4 "Big Boy" type built in 1941 by the American Locomotive Company (ALCO) at its Schenectady Locomotive Works. It was assigned to haul heavy freight trains in the Wasatch mountain range.The Chicago, Milwaukee, St. Paul & Pacific Railroad's own motive power department designed a Class S-1, 4-8-4 in 1930. It was built by the Baldwin Locomotive Works and put on the roster as number 9700. It remained the lone Northern on the CMStP&P for the next seven years.Each end of the double-ended locomotive has a four-wheel truck to guide the locomotive at speed, giving the R1 a 4-8-4 wheel arrangement in the Whyte notation (AAR: 2-D-2; UIC: 2'Do'2). Besides the R1, the PRR did not build or order any other 4-8-4 locomotives, however the T1 duplex was essentially a 4-8-4 with 2 sets of driving wheels, making ... The Santa Fe 2900 Class was a series of 30 4-8-4 type steam locomotives built between 1943 and 1944 for Atchison, Topeka and Santa Fe Railroad and pulled freight and passenger trains until retirement in the early to late-1950s. Today, six 2900s survive, with five units on static display and one, No. 2926, has been restored to operating ... Jun 19, 2006 · Canadian National and its subsidiaries owned North America’s largest fleet of 4-8-4s, including five streamlined versions built in 1936 to haul passenger trains between Montreal and Toronto. James Adams Dual-purpose Northerns followed, with examples going to Canadian National, Grand Trunk Western, Burlington, and Chicago & North Western. Get Updates. Canadian National U-class 4-8-4 locomotives proved to be the most versatile of the type operated in North America. It’s generally accepted that the ultimate in steam power was the 4-8-4 Northern type, if defined by criteria that includes speed, power, technology, and, perhaps most importantly, versatility.Union Pacific 4-8-4. Union Pacific class FEF-3 No. 841 stands for a builder's portrait at the American Locomotive Co. in 1944. The 10 FEF-3s were the final steam engines acquired by UP, which still operates one, No. 844, occasionally. Alco photo.4-8-4. Benefits. Better high speed performance. Drawbacks. Wheel slip. A 4-4-4-4 steam locomotive, in the Whyte notation for describing locomotive wheel arrangements, has a four-wheel leading truck, two sets of four driving wheels, and a four-wheel trailing truck. While it would be possible to make an articulated locomotive of this arrangement ... 4-8-4+4-8-4. Under the Whyte notation for the classification of steam locomotives by wheel arrangement, the 4-8-4+4-8-4 is a Garratt locomotive. The wheel arrangement is effectively two 4-8-4 locomotives operating back to back, with the boiler and cab suspended between the two engine units.Water cap. Canadian National 6213 is a preserved 4-8-4 steam locomotive on static display in Toronto, Ontario, Canada at the Toronto Railway Museum (TRM) on the lands of the former CPR John St. Roundhouse. It was on active duty until 1959 and was donated by Canadian National Railway (CNR) to the City of Toronto government in 1960. The Union Pacific FEF series consists of 45 4-8-4 "Northern" steam locomotives built by the American Locomotive Company (ALCO) between 1937 and 1944 and operated by the Union Pacific Railroad until 1959. The final steam locomotives built for the Union Pacific, the FEFs represented the apex of dual-service steam locomotive development in the ...4-8-4 Steam Locomotives. Category page. Edit. A 4-8-4 "Northern" is a type of wheel-arrangement for a large tender-type steam locomotive. Which refers to engines with 4 leading wheels, 8 driving wheels and 4 trailing wheels. To that end he ordered the company's superintendent of motive power and rolling equipment, E. Paul Gangewere, to get together with the design engineers at the Baldwin Locomotive Works to develop a plan to convert 30 of the railroad's I-10a 2-8-0 Consolidations to new 4-8-4 Northerns. These 30 steam locomotives (road numbers 2100 -2129) were ...4-8-4. The Northerns are steam locomotives that represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees ...Data from "4-8-4 Locomotives on the Northern Pacific," Baldwin Locomotives (1937), pp. 27-28 and NP to 1944 Locomotive Diagrams supplied in May 2004 by Allen Stanley from his extensive Rail Data Exchange. Works numbers were 62163-62166 in March 1938, 62167-62168. in April and 62169-62170 in May. As suggested by the 1937 account of the A-2s ... The Chicago, Milwaukee, St. Paul & Pacific Railroad's own motive power department designed a Class S-1, 4-8-4 in 1930. It was built by the Baldwin Locomotive Works and put on the roster as number 9700. It remained the lone Northern on the CMStP&P for the next seven years.4-8-4. Benefits. Better high speed performance. Drawbacks. Wheel slip. A 4-4-4-4 steam locomotive, in the Whyte notation for describing locomotive wheel arrangements, has a four-wheel leading truck, two sets of four driving wheels, and a four-wheel trailing truck. While it would be possible to make an articulated locomotive of this arrangement ...Data from "4-8-4 Locomotives on the Northern Pacific," Baldwin Locomotives (1937), pp. 27-28 and NP to 1944 Locomotive Diagrams supplied in May 2004 by Allen Stanley from his extensive Rail Data Exchange. Works numbers were 62163-62166 in March 1938, 62167-62168. in April and 62169-62170 in May. As suggested by the 1937 account of the A-2s ...The Delaware, Lackawanna & Western designed and purchased five 4-8-4s (road numbers 1501 through 1505) to increase its motive power for the "Lackawanna Limited" and other passenger trains. These locomotives were assigned Class Q-1 and were built by the American Locomotive Company after the Northern Pacific took delivery of the first 4-8-4s in 1927. Between 1936 and 1940 it built 28 Class O-5a Northerns (road numbers 5608 through 5635) in its own shops in W. Burlington, IA. All 36 of these locomotives had 74" drivers, 28 x 30 cylinders, 250 psi boiler pressure, and had a traction effort of 67,500 lbs. The first eight weighed 461,000 lbs and the balance weighed 473,700 pounds. The Lima-Southern Pacific GS-4 ("GS" meaning for "Golden State" or "General Service") is a type of semi-streamlined 4-8-4 Northern steam locomotive built by the Lima Locomotive Works in 1941 and 1942 specifically for the Southern Pacific (SP) Railroad. They were assigned road numbers 4430 through 4457. The GS-4s were principally employed on SP's famous "Daylight" streamliners from 1941, but in ...The Union Pacific FEF series consists of 45 4-8-4 "Northern" steam locomotives built by the American Locomotive Company (ALCO) between 1937 and 1944 and operated by the Union Pacific Railroad until 1959. The final steam locomotives built for the Union Pacific, the FEFs represented the apex of dual-service steam locomotive development in the ...Santa Fe 3751. Santa Fe 3759. Santa Fe Class 2900. South African Class 25 4-8-4. South African Class 25NC 4-8-4. South African Class 26 4-8-4. South Australian Railways 500 class (steam) South Australian Railways 520 class. Southern Pacific 4449.The Atchison, Topeka & Santa Fe bought a total of 65 4-8-4s, in four batches, all from the Baldwin Locomotive Works. The first group of 14 were delivered in 1927 (road number 3751), 1928 (road numbers 3752 through 3760) and 1929 (road numbers 3761 through 3764). Curiosly, 3751 was listed in Santa Fe's diagram book as a "Heavy Mountain".The St. Louis–San Francisco class 4500 was a class of 25 4-8-4 "Northern" type steam locomotives built by the Baldwin Locomotive Works between 1942-1943 and operated by the St. Louis–San Francisco Railway . The first three operated in passenger service, pulling trains such as the Meteor. The rest pulled freight throughout the system until ...The class used the 4-8-4 configuration of the modified 500B class, but was also designed for work on branch lines with light 60 lb/yd (29.8 kg/m) rail with a reduced tender load. The considerable weight of the locomotive was spread over eight axles, four driving and four in the leading and trailing trucks, yielding the necessary light axle ...Union Pacific rostered ten 4-10-2 locomotives that were three-cylindered machines developing 77,917 lbs of tractive effort on 63" drivers. They were a precursor to the 4-12-2 Union Pacific type, which was developed as a fast freight locomotive with 67-inch drivers and three cylinders, with a long shallow firebox supported by the training truck and drivers, similar to the firebox configuaraton ...The Nashville, Chattanooga & St. Louis Railroad bought five 4-8-4 locomotives in 1930, which they called "Dixies" (instead of "Northerns" - a name that would seem inappropriate on a fine southern railroad). These 1930 "Dixies" came from the American Locomotive Company and were designated Class J-2 and assigned road numbers 565 through 569.The 4-8-4's were given Class J and built by the master steam builders at N&W's Roanoke, Virginia shops. These machines could haul the mail, quite literally, and were the most powerful 4-8-4's ever built with tractive efforts reaching 80,000 pounds, boiler pressures of 300 psi, and perfectly couter-balanced to reach unimaginable speeds of 140 mph!The Southern Pacific GS-4 is a class of streamlined 4-8-4 "Northern" type steam locomotive operated by the Southern Pacific Railroad (SP) from 1941 to 1958. A total of twenty-eight were built by the Lima Locomotive Works, numbered 4430 through 4457. GS stands for "Golden State" or "General Service." Unlike the GS-3, the GS-4 had a dual ...Fred McLeod. Union Pacific 4-8-8-4 No. 4023 prepares to depart Cheyenne, Wyo., with a westward freight in May 1954. E.C. Storm. It was, more or less, an eight-coupled Challenger. The locomotive boasted both the adhesion of an eight-coupled articulated, needed to haul heavy trains, and large 68-inch driving wheels (only 1-2 inches smaller than ...Dec 20, 2016 · The Big Boy utilized a 4-8-8-4 wheel arrangement and was the only locomotive to do so. At the front of the engine was a four-wheel leading truck that had 36 in (.91 m) wheels. This was followed by eight 68 in (1.73 m) drive wheels, with a single piston driving a set of four wheels on each side of the engine. The Minneapolis, St. Paul & Sault Sainte Marie Railroad purchased four Class O-20, 4-8-4s in 1938 from the Lima Locomotive Works. They were given road numbers 5000 through 5003 and were assigned to both freight and passenger trains. These locomotives were designed with 75" drivers, 26 x 32 cylinders, a 270 psi boiler pressure, a weight of ...The B&O bought thirteen 4-8-2s from the Boston & Maine. They were given road numbers 5650 through 5662 and were designated as Class T-4 and were used until 1958. There are no surviving B&O "Mountains". The Class Ts (numbers 5500 & 5501) were scrapped in 1953. In the early 1940s, the Missouri Pacific Railroad converted all 25 of its 2-8-4 Berkshires into 4-8-4 Northerns. These rebuilt locomotives (road numbers 2101 through 2125) were given 75" drivers, greater boiler capacity, a cast steel engine bed and roller bearings on all axles. They had 28 x 30 cylinders, a boiler pressure of 250 psi, a total ... The Minneapolis, St. Paul & Sault Sainte Marie Railroad purchased four Class O-20, 4-8-4s in 1938 from the Lima Locomotive Works. They were given road numbers 5000 through 5003 and were assigned to both freight and passenger trains. These locomotives were designed with 75" drivers, 26 x 32 cylinders, a 270 psi boiler pressure, a weight of ...A 4-8-8-4 in the Whyte notation for the classification of steam locomotives by wheel arrangement, is a locomotive with a four-wheel leading truck, two sets of eight driving wheels, and a four-wheel trailing truck. Only one model of locomotives has ever used this configuration, and that is commonly known as "Union Pacific Big Boys" after the ...4-8-4+4-8-4. Under the Whyte notation for the classification of steam locomotives by wheel arrangement, the 4-8-4+4-8-4 is a Garratt locomotive. The wheel arrangement is effectively two 4-8-4 locomotives operating back to back, with the boiler and cab suspended between the two engine units.The Union Pacific Big Boy is a type of simple articulated 4-8-8-4 steam locomotive manufactured by the American Locomotive Company (ALCO) between 1941 and 1944 and operated by the Union Pacific Railroad in revenue service until 1962. The 25 Big Boy locomotives were built to haul freight over the Wasatch Range between Ogden, Utah, and Green ...Water cap. Factor of adh. Norfolk and Western 475 is a 4-8-0 "Mastodon" type steam locomotive built by the Baldwin Locomotive Works in June 1906 as part of the Norfolk and Western Railway's (N&W) first order of M class numbered 375–499. It was first assigned to haul freight trains on the N&W mainline before being reassigned to branch line ...
The Union Pacific Railroad bought 45 4-8-4s in three orders from the American Locomotive Company. The second order of 15 locomotives (road numbers 820 through 834) was delivered in 1939. These locomotives were designated as Class FEF-2. They were designed to have 80" drivers, 25 x 32 cylinders, a boiler pressure of 300 psi, and a weight of 483,. Exterior semi gloss enamel paint
Left: The NYC HS-1a of 1931. No.800. This 4-8-4 compound locomotive was an experiment built in 1931 by ALCO for the New York Central Railroad. It carried road number 800 and was designated Class HS-1a. It did poorly on test runs and was used only as a hump shunting engine at Selkirk yard until it was scrapped in 1939. It has flaws, but Broadway Limited Imports has shown an ability to learn from mistakes. Fans of western steam power will be happy to have it and to look forward to comparing BLI releases of Santa Fe (and Union Pacific) locomotives. HO Santa Fe 4-8-4. Price: $329.99. Manufacturer:In the case of a long locomotive like the Big Boy, articulation allowed the engine to operate on tracks with curves as sharp as 20 degrees. ALCO built the Big Boys in Schenectady, New York, and two versions of the engine were made. Starting in 1941, 20 of the 4-8-8-4-1 class engines were made and numbered 4000–4019.October 4, 2000. Atchison, Topeka and Santa Fe 3751 is a class 3751 4-8-4 "Heavy Mountain" type steam locomotive built in May 1927 by the Baldwin Locomotive Works in Eddystone (Philadelphia), Pennsylvania for the Atchison, Topeka & Santa Fe Railway (ATSF). No. 3751 was the first 4-8-4 steam locomotive built for the Santa Fe and was referenced ... A private Railway operating in New Zealand at the time exclusively purchased Baldwin products after facing the same difficulties with British builders the NZR had. The Wellington & Manawatu Railway (1881–1909) operated small fleets of 2-8-0 (4), 2-6-2 (6), 2-8-2 (1), 4-6-0 (2) and a large 2-8-4 (1) tank locomotive. When the NZR took over the ... The big J3 engine, the sole survivor of a class of 20 built during the desperate days of World War II, is a 1942 product of the American Locomotive Company. The last time someone proposed removing the 4-8-4 from Centennial Park, in 2001, the parks board declined the offer.The Union Pacific Railroad bought 45 4-8-4s in three orders from the American Locomotive Company. The second order of 15 locomotives (road numbers 820 through 834) was delivered in 1939. These locomotives were designated as Class FEF-2. They were designed to have 80" drivers, 25 x 32 cylinders, a boiler pressure of 300 psi, and a weight of 483, Union Pacific 4-8-4 #838, featuring classic elephant-ear smoke deflectors, appears to be slowly backing towards the water plug in Council Bluffs, Iowa on September 21, 1958. By the date of this photo the locomotive was finishing up its last days in freight service before retirement. Bernard Corbin photo. American-Rails.com collection. History4-8-4. The Northerns are steam locomotives that represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees ...4-8-2. Under the Whyte notation for the classification of steam locomotives, 4-8-2 represents the wheel arrangement of four leading wheels, eight powered and coupled driving wheels and two trailing wheels. This type of steam locomotive is commonly known as the Mountain type. [1] The Great Northern Railway obtained its first "Northerns" in 1929, when six Class S-1s were delivered from the Baldwin Locomotive Works. These 4-8-4s were given road numbers 2550 through 2555 and had 73" drivers, 28 x 30 cylinders, a boiler pressure of 250 psi, a weight of 472,120 lbs and a tractive effort of 68,466 pounds. The St. Louis Southwestern Railroad acquired Northerns at three different times. It bought 10 Class L-1 Northerns in 1930 from the Baldwin Locomotive Works and assigned them road numbers 800 through 809. These 4-8-4s were oil burners with 70" drivers, 26 x 30 cylinders, a boiler pressure of 250 psi, a weight of 419,800 lbs and a tractive effort ... Santa Fe 2926 is a former Atchison, Topeka and Santa Fe Railway (ATSF) class 2900 4-8-4 type steam locomotive, built by Baldwin in 1944. It was used to pull passenger and fast freight trains, mostly throughout New Mexico until it was retired from revenue service in 1956. It was subsequently donated to a park in Albuquerque for static display.Nov 1, 2004 · It has flaws, but Broadway Limited Imports has shown an ability to learn from mistakes. Fans of western steam power will be happy to have it and to look forward to comparing BLI releases of Santa Fe (and Union Pacific) locomotives. HO Santa Fe 4-8-4. Price: $329.99. Manufacturer: 4-8-2. Under the Whyte notation for the classification of steam locomotives, 4-8-2 represents the wheel arrangement of four leading wheels, eight powered and coupled driving wheels and two trailing wheels. This type of steam locomotive is commonly known as the Mountain type. [1] The Ferrocarriles Nacionales de Mexico (National Railways of Mexico) bought a total of 32 Northern type, Class QR-1, locomotives in 1946. NdeM purchased 16 from the American Locomotive Company and 16 from the Baldwin Locomotive Works. On the NdeM these locomotives were called "Niágaras" and were among the few that it bought new.05001557. Added to NRHP. January 25, 2006. Spokane, Portland & Seattle 700 is the oldest and only surviving example of the class "E-1" 4-8-4 "Northern" type steam locomotive and the only surviving original Spokane, Portland and Seattle steam locomotive. It was built by the Baldwin Locomotive Works in May 1938. Improved HO 4-8-4 has looks and power. This HO 4-8-4 from Rivarossi is a welcome upgrade to an accurate and attractive model originally introduced in 1980. The new engine features RP-25 wheels, improved electrical pickup, flywheel drive, increased weight for traction, and wiring for plug-in installation of Digital Command Control (DCC). .